https://www.reddit.com/r/3Dprinting/comments/kgdmu8/3d_printing_with_a_1mm_nozzle_absolutely_devours/

AllImages Videos News Maps Shopping Books

3D printing with a 1mm nozzle absolutely DEVOURS filament like ...

Dec 19, 2020 · 3D printing with a 1mm nozzle absolutely DEVOURS filament like theres no tomorrow ... This video cannot be played. ... If using a 1mm nozzle it is ...

r/3Dprinting - Reddit

www.reddit.com › ...

r/3Dprinting: /r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of…

Wiki · R/3D Printing! Come for the... · Purchase Advice Megathread · Hot

Missing: kgdmu8/ 3d_printing_with_a_1mm_nozzle_absolutely_devours/

L'impression 3D avec une buse de 1 mm DÉVOURE absolument le ...

www.reddit.com › comments › kgdmu8

Dec 19, 2020 · 57 votes, 38 comments. 2,3 M subscribers in the 3Dprinting community. /r/3DPrinting is a place where makers of all skill levels and walks of ...

Is a 0.1mm nozzle good? : r/3Dprinting - Reddit

www.reddit.com › comments

Dec 31, 2021 · I've been told anything below 0.2mm will clog so often it's not worth it. I've done some prints with 0.25mm nozzles and the main downside was ...

Missing: kgdmu8/ 3d_printing_with_a_1mm_nozzle_absolutely_devours/

Trying out a 1mm nozzle : r/FixMyPrint - Reddit

www.reddit.com › FixMyPrint › comments

Feb 9, 2024 · I'm printing PLA at 220°C, 0.4mm layer height, at 30mm speed. Also, when printing I can clearly hear the filament popping, which does not happen ...

Missing: kgdmu8/ 3d_printing_with_a_1mm_nozzle_absolutely_devours/

1mm nozzle and 1mm layer go brrr : r/3Dprinting - Reddit

www.reddit.com › comments

Mar 10, 2023 · So with a 1mm nozzle, 0.75mm should be your maximum layer height for decent adhesion. Using a layer height equal to the nozzle diameter ...

Missing: kgdmu8/ 3d_printing_with_a_1mm_nozzle_absolutely_devours/

What you make of this? : r/3Dprinting - Reddit

www.reddit.com › comments › what_yo...

Jan 15, 2023 · Hey! Fairly new to 3d. I've leveled the bed to 1mm and using standard pla at 60/200 degrees. But one side doesn't appear to be sticking and ...

Missing: kgdmu8/ 3d_printing_with_a_1mm_nozzle_absolutely_devours/

Used a 1.0 mm nozzle for the vase and decided to print a sturdy doggo ...

www.reddit.com › comments › used_a_1...

Feb 12, 2020 · I've been using a 1mm nozzle on my CR-10 for the last few weeks. It's great for fast, functional prints. .5mm layer height, slowed it down ...

Missing: kgdmu8/ 3d_printing_with_a_1mm_nozzle_absolutely_devours/

I have a question : r/3Dprinting - Reddit

www.reddit.com › comments › i_have_a...

Dec 1, 2022 · So I've been going through CGtrader and have found some good miniatures that I would like to pay someone to print is that a violation of a ...

Missing: kgdmu8/ 3d_printing_with_a_1mm_nozzle_absolutely_devours/

just dug up my first ever print : r/3Dprinting - Reddit

www.reddit.com › comments › just_dug...

Dec 19, 2022 · just dug up my first ever print · Welcome to R/3D Printing! Come for the Benchy, stay for the Calibration! · More posts you may like · Top Posts ...

Missing: kgdmu8/ 3d_printing_with_a_1mm_nozzle_absolutely_devours/

In order to show you the most relevant results, we have omitted some entries very similar to the 10 already displayed. If you like, you can repeat the search with the omitted results included.